![]() ![]() In the putty state Milliput, like most chemicals in domestic use, may cause irritation to sensitive skins. If the putty is allowed to harden on it will be almost impossible to remove. When tools have been used for applying or contouring Milliput they should be cleaned immediately after use. To obtain a smooth finish, mould or apply Milliput and then immediately wipe and smooth gently with wet finger or with a fine textured moist cloth. There are certain instances when work may be carried out in a gentle stream of water under a tap. To aid manipulation and avoid sticking, fingers and tools should be kept moistened with water. the putty may now be applied and will set hard in three to four hours without shrinking.Īt all stages from initial mixing to final setting Milliput responds to the use of water. Abrading the surface will improve adhesion. Smooth surfaces should be cleaned with a suitable solvent or with soap and warm water to remove dirt and grease. The surfaces to which the putty is applied should be free from grease and dirt. Knead and roll in the hands for at least 5 minutes until the colours merge and become uniform and no streaks can be seen, and then mix for another minute. Mix together equal parts of each stick from the pack. Milliput will set under water and is heat resistant up to 130*C. Milliput is an excellent adhesive and will bond any of the following to itself or to any of the others - wood, brick, cement, metals, concrete, plastics, glass etc, but note that Milliput is not intended as a thin layer adhesive. Once fully cured Milliput can be machined, drilled, tapped, turned, filed, sawn, sandpapered and painted. By the application of heat the setting time can be reduced.Īfter setting hard Milliput continues to cure and is fully cured after an elapse of time equal to the setting time at the same temperature. Speed of hardening is dependant on temperature and at normal temperatures (20-25 deg C) Milliput becomes rock hard in three to four hours. Once equal quantities of each stick have been mixed the resultant putty is at first soft and highly adhesive and then gradually hardens. sticks and the general instructions for preparation and usage are the same. Each grade is presented in similar packs containing 2 x 56*7gm. At all stages from initial mixing to final setting Milliput responds to the use of water.Milliput produces five grades of epoxy putty: Standard (Yellow/Grey), Terracotta, Silver Grey, Black and Superfine White. the putty may now be applied and will set hard in three to four hours without shrinking. ![]() How long does it take to set Milliput with putty? Milliput can be used for repairs on many types of materials including metals, plastics, masonry, wood, glass and ceramics and can be used in places where welding is impractical. Milliput products are available from most leading model/hobby shops, art and craft suppliers, independent hardware stores and plumbers merchants. It is: Keep a pack of Milliput in your tool box for those urgent emergency repairs. Why Milliput? The Most Versatile Material Available. superfine white is superfine as the name states, and silver-grey is somewhere in between. How long does milliput take to cure? What is the difference between milliput colors?įrom experience black, terracota and yellow/grey are exactly the same texture, just different colors. ![]() ![]() Small quantities should be used to avoid creating a very wet mix that may be difficult to mix. Liquid colourings, like enamel paints, oil paints, spirit based-dyes or pigments can also be used to colour Milliput, but liquids or pastes may be difficult to introduce into the putty. By the application of heat the setting time can be reduced to a few minutes. Speed of hardening is dependant on temperature and at normal temperatures (20-25✬) Milliput becomes rock hard in three to four hours. It has excellent adhesion to stone, ceramic, metal, wood and many plastics, including vinyl. Kneadatite Blue/Yellow (Green Stuff) is a two-part epoxy/polyamide sealant/adhesive for interior and exterior maintenance and repair. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |